"workover drilling rig"
API 4F 掘削リグ 基礎構造 リグ 床のサポートのための鋼筋枠
The substructure is the large steel framework assembled directly over the drilling site that supports the entire rig floor, mast, rotary table, drawworks, and all associated drilling equipment. It is the foundation upon which the entire drilling operation rests. Unlike the mast which rises ...
合金鋼掘削リグ部品 ホイスト・循環装置用スイベル API 8C
Swivel – API 8C Hoisting & Circulation Equipment for Drilling Rigs Product Overview A swivel is a critical piece of hoisting and circulating equipment on a drilling rig or workover rig. It hangs directly beneath the travelling block and above the kelly drive (or top drive), serving as the vital link ...
API 7K掘削リグ巻上げ装置（ホイスト作業用）
The drawworks is the primary hoisting mechanism on a drilling rig. Essentially, it is one large winch that spools off or takes in the drilling line — a heavy-duty wire rope — to raise or lower the drill stem, drill bit, casing strings, and completion equipment through the crown block and traveling ...
スキッド搭載深井掘削リグ 4000mから9000m 最大静的負荷 6750kNまで
Skid-Mounted Drilling Rig – Deep Well Drilling from 4,000m to 9,000m Product Overview Our skid-mounted drilling rig series is designed for deeper drilling operations, covering nominal depths from 4,000 m up to 9,000 m, with maximum static loads ranging from 2,250 kN to 6,750 kN. These rigs are ...
油田钻井用卡车式钻机 机械液压驱动
Truck-Mounted Drilling Rig – Reliable Shallow to Medium-Deep Well Drilling Product Overview Our truck-mounted drilling rig combines mechanical and hydraulic drive systems. All major components – including the power system, drawworks, mast, traveling system, and transmission – are installed on a self...
掘削作業リグ用トラベリングフックブロック一体型巻上システム
T he travelling hook block is a lifting device used on drilling and workover rigs, which takes an integral design integrating the travelling block and the hook into a single unit. By eliminating the conventional detachable coupling between the block and the hook, this integral design shortens the ...
モジュラルの油井改造リグ 厳しい凍結条件下で乗組員を保護する
Cold Weather Workover Rig – Reliable Well Servicing Down to -45°C Product Overview Our cold weather workover rigs are specifically designed for operation in extreme low-temperature environments. Every component is built to perform reliably under severe cold conditions. These rigs focus on two goals: ...
トレーラーに搭載された油田転用リグ API 7K移動井戸サービスユニット
API 7K Trailer-Mounted Workover Rig | Mobile Well Servicing Unit High-Efficiency, Rapid-Deployment Solution for Onshore Well Intervention Our Trailer-Mounted Workover Rig is a highly mobile, self-contained well servicing unit designed specifically for onshore oil and gas operations. Engineered to ...
機械油圧駆動自走シャーシ付きトラック搭載石油掘削リグ
Truck-Mounted Workover Rig – Efficient Well Servicing from 2,500m to 7,000m Product Overview This truck-mounted workover rig uses a mechanical and hydraulic drive system. The power system, drawworks, mast, traveling assembly, and transmission are all installed on a self-propelled chassis. This ...
石油・ガス掘削泥水処理固形物管理システム
S olid Control System – Complete Drilling Fluid Processing for Oil & Gas Operations Product Overview A solid control system is a comprehensive equipment package used in oil and gas drilling to maintain the properties of drilling fluid (mud). Also known as a mud circulation system, it removes drilled ...
水力管の電源タング API 7K 井戸サービスと作業作業のために
Hydraulic Tubing Power Tong – API 7K Hydraulic Power Tong for Well Service & Workover Operations A hydraulic tubing power tong is a speciali z ed hydraulic power tool designed for making up (tightening) and breaking out (loosening) threaded connections on tubing, sucker rods, small casing strings, ...
掘削・作業作業用 API 16A 統合 BOP スタック統合坑井制御システム
アニュラーBOP、ラムBOP、ドリリングスプールを単一の鍛造ユニットに統合した一体型BOPスタック。コンポーネント間の接続を排除し、漏れ箇所を減らします。スペースが限られたリグに最適です。 API 16A および GOST に準拠。ボアサイズは 7‑1/16 インチ～21‑1/4 インチ、圧力は最大 70 MPa。
