"workover drilling rig"
Стальная рама буровой установки API 4F для поддержки пола буровой установки
The substructure is the large steel framework assembled directly over the drilling site that supports the entire rig floor, mast, rotary table, drawworks, and all associated drilling equipment. It is the foundation upon which the entire drilling operation rests. Unlike the mast which rises ...
Части буровой установки из сплавной стали Swivel API 8C для подъемного и циркуляционного оборудования
Swivel – API 8C Hoisting & Circulation Equipment for Drilling Rigs Product Overview A swivel is a critical piece of hoisting and circulating equipment on a drilling rig or workover rig. It hangs directly beneath the travelling block and above the kelly drive (or top drive), serving as the vital link ...
Лебедка буровой установки API 7K для спускоподъемных операций
The drawworks is the primary hoisting mechanism on a drilling rig. Essentially, it is one large winch that spools off or takes in the drilling line — a heavy-duty wire rope — to raise or lower the drill stem, drill bit, casing strings, and completion equipment through the crown block and traveling ...
Скид монтированная глубокая скважина сверлильная установка 4000м до 9000м с максимальной статической нагрузкой до 6750kN
Skid-Mounted Drilling Rig – Deep Well Drilling from 4,000m to 9,000m Product Overview Our skid-mounted drilling rig series is designed for deeper drilling operations, covering nominal depths from 4,000 m up to 9,000 m, with maximum static loads ranging from 2,250 kN to 6,750 kN. These rigs are ...
Грузовики для бурения нефтяных месторождений Механический гидравлический привод для бурения скважин
Truck-Mounted Drilling Rig – Reliable Shallow to Medium-Deep Well Drilling Product Overview Our truck-mounted drilling rig combines mechanical and hydraulic drive systems. All major components – including the power system, drawworks, mast, traveling system, and transmission – are installed on a self...
Подвижный крюковой блок интегрированной подъемной системы для буровых и ремонтно-монтажных установок
T he travelling hook block is a lifting device used on drilling and workover rigs, which takes an integral design integrating the travelling block and the hook into a single unit. By eliminating the conventional detachable coupling between the block and the hook, this integral design shortens the ...
Модульная нефтяная скважина для переработки нефти повышает защиту экипажа в суровых условиях заморозки
Cold Weather Workover Rig – Reliable Well Servicing Down to -45°C Product Overview Our cold weather workover rigs are specifically designed for operation in extreme low-temperature environments. Every component is built to perform reliably under severe cold conditions. These rigs focus on two goals: ...
Прицепные нефтеперерабатывающие установки API 7K Мобильная служба скважин
API 7K Trailer-Mounted Workover Rig | Mobile Well Servicing Unit High-Efficiency, Rapid-Deployment Solution for Onshore Well Intervention Our Trailer-Mounted Workover Rig is a highly mobile, self-contained well servicing unit designed specifically for onshore oil and gas operations. Engineered to ...
Грузовик с механическим гидравлическим приводом
Truck-Mounted Workover Rig – Efficient Well Servicing from 2,500m to 7,000m Product Overview This truck-mounted workover rig uses a mechanical and hydraulic drive system. The power system, drawworks, mast, traveling assembly, and transmission are all installed on a self-propelled chassis. This ...
Система твердого контроля бурения нефти и газа
S olid Control System – Complete Drilling Fluid Processing for Oil & Gas Operations Product Overview A solid control system is a comprehensive equipment package used in oil and gas drilling to maintain the properties of drilling fluid (mud). Also known as a mud circulation system, it removes drilled ...
Гидравлические трубные силовые штыки API 7K для работы с колодцами
Hydraulic Tubing Power Tong – API 7K Hydraulic Power Tong for Well Service & Workover Operations A hydraulic tubing power tong is a speciali z ed hydraulic power tool designed for making up (tightening) and breaking out (loosening) threaded connections on tubing, sucker rods, small casing strings, ...
Интегральная система управления скважиной API 16A для бурения и переработки
Интегрированный блок противовыбросовых превенторов, объединяющий кольцевой противовыбросовый превентор, плашечный противовыбросовый превентор и буровую катушку в одном кованом блоке. Устраняет межкомпонентные соединения, уменьшая места утечек. Идеально подходит для буровых установок с ограниченным пространством. Соответствует API 16A и ГОСТ. Диаметры отверстий 7‑1/16″–21‑1/4″, давление до 70 МПа.
